Licence Plate Holder For CFMOTO 450MT - 2024-2027

Direct Fit License Plate Bracket for CFMOTO 450MT 2024 2025 2026 2027

This fender eliminator bracket is designed specifically for the CFMOTO 450MT subframe geometry. It uses the existing factory mounting points where the OEM fender assembly bolts on, so installation requires no drilling, no cutting, and no permanent modification to your motorcycle. You remove the stock fender, bolt this bracket into position using the included stainless steel hardware, relocate your license plate and plate light, and the job is done. Total install time is about 20 to 30 minutes with basic hand tools.

Fitment is confirmed for all CFMOTO 450MT model years currently in production: 2024, 2025, 2026, and 2027. That includes both the standard 450MT and any adventure or touring trim variants that share the same rear subframe and fender mounting points. If CFMOTO hasn't changed the subframe geometry on your specific model year, this bracket fits.

CNC Aluminum Construction and Anodized Finish

The bracket itself is CNC-machined from aluminum alloy, giving it a strength-to-weight ratio that the factory plastic fender can't match. Where the OEM assembly flexes and vibrates at highway speed, this plate holder stays rigid and rattle-free because the material and the mounting geometry are engineered to handle sustained vibration loads from both the engine and road surface inputs.

The surface finish is black anodized, which serves two purposes. First, it gives the bracket a clean, understated appearance that blends with the 450MT's tail section and black subframe rather than drawing attention to itself. Second, anodizing creates a hard oxide layer on the aluminum surface that resists scratching, corrosion, and UV fading far better than paint or powder coat alone. Salt spray from winter roads, trail mud, pressure washing, chain lube overspray: the anodized finish handles all of it without degrading over time.

All mounting hardware included in the kit is stainless steel. Aftermarket brackets in this price range frequently ship with plain zinc-plated bolts that rust within a few months of exposure. Stainless hardware means you're not dealing with seized, corroded fasteners when you need to remove the bracket for maintenance or tire changes two years from now.

LED License Plate Light and Turn Signal Compatibility

The kit includes a built-in LED license plate light that mounts directly to the bracket, illuminating your plate for legal compliance without adding a separate dangling light assembly. The LED unit is compact and sits flush against the bracket body so it doesn't disrupt the clean profile you're installing this kit to achieve in the first place.

For turn signals, the bracket is designed to work with the CFMOTO 450MT's OEM rear indicators. You can either relocate the factory signals to the new bracket position using the included mounting provisions, or upgrade to compact aftermarket LED turn signals that bolt onto the integrated signal mounts. Many riders take the opportunity to swap in flush-mount or mini LED indicators at the same time as the tail tidy install, since you already have the rear end apart and the wiring accessible.

Wiring for the plate light is plug-and-play with the existing harness. No splicing, no soldering, no aftermarket relay needed. You connect to the stock wiring that previously fed the OEM plate light, and the LED unit draws so little current that there's zero risk of overloading the circuit or triggering any electrical issues.

Why Replace the Stock Fender on Your CFMOTO 450MT

Beyond the visual improvement, there are practical reasons to ditch the factory fender setup on the 450MT. The OEM fender is a mud and water trap. Its large surface area catches road spray, dirt, and debris on every ride, caking the underside of the tail section with grime that's difficult to clean and accelerates wear on the components it covers. With the tail tidy installed, water and debris pass through instead of collecting, which means less cleaning and less corrosion risk for the wiring, connectors, and fasteners in the tail area.

Weight reduction is modest but real. The stock fender assembly with its brackets, reflectors, and hardware weighs more than most riders expect. The aluminum tail tidy bracket and LED plate light weigh a fraction of that. On a middleweight adventure bike like the CFMOTO 450MT, every gram you remove from the rear overhang improves the visual balance of the motorcycle and marginally reduces unsprung feel at the tail.

What's Included in the CFMOTO 450MT Fender Eliminator Kit

The kit ships complete and ready to install. You receive the main CNC aluminum bracket, the integrated LED license plate light, all stainless steel mounting bolts and spacers, and a wiring adapter for plug-and-play connection to the CFMOTO 450MT stock harness. No additional parts, brackets, or adapters are required. Everything you need to go from stock fender to clean tail tidy is in the box.

Compatible with CFMOTO 450MT 2024, CFMOTO 450MT 2025, CFMOTO 450MT 2026, CFMOTO 450MT 2027. Fits all trim levels with standard OEM rear subframe and fender mounting provisions.

Free shipping on every order in the US. Every part is covered by a 1-year warranty and can be returned within 30 days of receipt.